File size: 54.6 MB

Software for the computation of bearing capacity on loose or rocky soils, according Terzaghi, Meyerhof, Hansen, Vesic, Brinch-Hansen, Richards et. Al, Meyerhof and Hanna (1978) and computation of bearing capacity factors. Settlements: Elastic (Timoshenko and Goodier), Oedometric, Schmertmann, Burland & Burbidge, liquefaction using the method of Seed and Idriss (1971).

Analysis of soil reinforced with geogrids, calculation of: increase bearing capacity, deformation in the reinforcements, tensile force in the reinforcement for membrane effect.
Bearing capacity and settlments - Loadcap: calculated at any point either inside or outside the foundation.
Bearing capacity in seismic conditions: SHIKHIEV & JAKOVLEV, RICHARDS

Diagrams: Bearing capacity as a function of the foundation base, of the depth of the bearing surface, of the acting loads. Unlimited number of layers. Display of pressure bulbs and failure wedges.

Supported computation standards:
• Eurocode 7/8
• British Codes BS8004
• SR EN 1997-1/NB/2007
• Other standard.

DATA INPUT
• Multi level undo-redo
• Numeric input in tabular form
• Graphic input
• Automatic conversion of measurement units

DATA INPUT
• Strip footing; Spread footing; Mat foundation; Circular foundation; Foundation on slope
• Bearing capacity according to: Terzaghi, Meyerhof, Hansen, Brinch-Hansen, Vesic, Zienkiewicz, Eurocode, Meyerhof and Hanna (1978)
• Settlements: Elastic, Oedometric, Schmertmann, Burland & Burbidge with progress over time
• Presence of Gorund Water Table. Downloaded from sanet.sd
• Permanent settlements after the earthquake: Idriss and Boulanger, Pradel, Yasuhara and Andersen
• Analysis in terms of total and effective stresses
• Display of pressure bulb and failure wedges 2D, 3D
• Computation of the stress state induced by external loads at any point
• Analysis in relation to total and effective tension
• Seismic corrections: SHIKHIEV & JAKOVLEV
• Display of tensional state and pressure bulb
• Computation of stress state induced by external loads at any point
• Nspt correlation with geotechnical parameters according to: Meyerhof, Sanglerat & Peck, Hanson and Thorburn
• Verification to translation
• Analysis of embedded plans
• Automatic reading of stratigraphic columns generated by Stratigrapher software
• Data exchange with Micropiles and Piles for foundations software
• Automatic computation of loads acting on foundation
• Computation of tensions: Boussinesq,Westergaard
• Interactive graphic construction
• Multi level undo-redo function
• Embankment analysis and settlement computation
• Differential settlements 3D

COMPUTATION OPTIONS
• Computation of the bearing capacity for multi layered soils using a weighted averages and punching verification
• Foundations on slopes
• Foundations with inclined bearing surface
• Foundations subject to eccentric loads
• Generating the bearing capacity table as a function of depth and width, exportable in Excel or in memory
• Construction of graphics allowable load-depth
• Construction of graphics allowable load-foundation width
• Load - settlement diagram
• Computation of subgrade reaction modulus using the model of Terzaghi and Bowles
• Water table, even above the bearing surface
• Display of pressure bulbs - Boussinesq or Westergaard
• Display of stress states in any point of the foundation soil
• Display of failure wedges
• Setup of influence area
• Computation of oedometric settlements in any point inside or outside the foundation

Whats New:
Check limit load (SLU)
Subgrade reaction costant calculated according: K=E/L*(1-Poisson^2)
Major version Loadcap 2017
• General improvements;
• Implemented analytical solutions for estimating the ultimate bearing capacity of geogrid reinforced soil foundations (RSF) for both sand and silty clay soils;
• Method Vesic 1975 Change depth and form factor;
• Opening files with drag&drop;
• Standards upgrade: NTC 2017, SR EN 1997-1/NB/2007;
• Calculating seismic parameters for areals in Central and Eastern Europe;
• Plugin management: Embankment (Embankment settlements ), Overturning (Foundation overturning Safety factor), Converting User Units;
• Update of System components.
x.824: Fix Save as function for the computation report and color selection for the stratigraphy

HOMEPAGE




Download From Uploadgig



Download From Rapidgator



Download From Nitroflare